Guide for student pilots

How to read a VFR chart

A VFR chart is a map drawn for pilots. It shows where the ground is high, where the airspace starts and stops, where the aerodromes and radio beacons are, and which landmarks you can see from the air. This guide goes through an ICAO 1:500,000 chart section by section, with a symbol quiz and an exercise in measuring a track.

Last checked: 17 November 2026. Written for training. The symbols on this page are simplified drawings made for VectorEFB. They follow the general conventions of ICAO Annex 4, but the legend printed on your own chart always prevails.

1. What you are looking at

The standard for aeronautical charts is ICAO Annex 4, with the Aeronautical Chart Manual (Doc 8697) as guidance. Annex 4 describes an Aeronautical Chart at 1:500,000 that many countries use as their VFR chart. Some countries also publish sheets at larger scales, such as 1:250,000, for busy or training areas, and some use their own style. The scale, the projection and the symbols vary from one publisher to the next.

So the first job with any chart is to read the legend and the margin notes. Look for the scale, the projection, the date of the data, the units of height (feet or metres) and the key to the colours. Everything below describes the usual pattern, not a rule that holds on every sheet.

Check the date on a paper chart. Airspace, obstacles and frequencies change. An out-of-date chart is a planning risk, and the current AIP and notices come first.

2. Scale: how far is a centimetre?

The scale is a ratio. At 1:500,000, one unit on paper stands for 500,000 of the same unit on the ground. One nautical mile is 185,200 centimetres, so on a 1:500,000 chart it takes up 185,200 ÷ 500,000 = 0.37 cm, a little under 4 mm.

Chart scale1 cm on paper is1 nm on paper is
1:1,000,00010 km (5.4 nm)1.85 cm
1:500,0005 km (2.7 nm)0.37 cm
1:250,0002.5 km (1.35 nm)0.74 cm

A useful habit on a 1:500,000 chart: 10 nm is about 3.7 cm, and 10 cm is about 27 nm. Plotters and rulers made for aviation have these scales printed on them. If you print a chart or zoom on a screen, the printed scale bar stays true and the ratio does not, so measure against the bar.

3. Projection: why a straight line works

The Annex 4 1:500,000 chart is drawn on a Lambert conformal conic projection. The surface of the earth is projected onto a cone that cuts the earth along two standard parallels, and the cone is then unrolled. The legend names the standard parallels. Two things follow from it:

  • Angles are true. The angle between two lines on the chart equals the angle on the ground, so a plotter reads true tracks directly.
  • A straight line is close to a great circle. For a VFR leg you can draw it straight and fly it as one track.

Meridians are not parallel on the chart. They lean towards each other as you go north, and this is called convergence. On a long leg the track angle is slightly different at each end. At 45°N, a leg of 100 nm east or west changes the track by about 1.7° from one end to the other. For this reason you measure a track where the line crosses a meridian near the middle of the leg. The lesson on chart projections, great circles and convergence shows why.

4. Terrain: tints, contours, spot heights and the maximum elevation figure

Relief is drawn in several ways at once, and a good reading uses all of them.

  • Elevation tints. Bands of colour show height bands, usually green for low land and then yellow, tan and brown as the land rises. The key in the margin lists the bands, and the height steps differ between charts.
  • Contour lines. Each line joins points at the same height. Lines drawn close together mean steep ground. Some lines are labelled, so you can count up or down.
  • Spot heights. A dot and a figure give the elevation of a single point above mean sea level, typically a hill top, a pass or a bridge.
  • Maximum elevation figure (MEF). Many VFR charts print one large figure in each quadrangle of the latitude and longitude grid. It is the highest terrain or obstacle in that block, often rounded up. It is a fast first look at a safe altitude over a block. It does not replace a margin of your own, and its construction is explained in the legend.

As a habit, run your eye along the planned track and a few miles each side of it. Note the highest figure you find, then compare it with the altitude you plan to fly and with the cloud base in the forecast. The cross-country planning guide goes on from there.

5. Obstacles

Masts, towers, chimneys and wind turbines are drawn as small spires or tower shapes. A group of obstacles has its own symbol, and a lit obstacle is drawn with rays. The figures normally give the height of the top above mean sea level, and on many charts the height above ground follows in brackets. Taller than about 100 m above ground, and in some countries lower, they are the objects most likely to be charted, but small obstacles and cables are not always shown. Wires are the usual example, so treat low flying with caution even when the chart looks empty.

6. Aerodromes

Aerodromes are drawn as circles in a strong colour, often magenta or blue. A circle with runway lines means a land aerodrome with a hard runway. Other patterns show unpaved strips, heliports, gliding sites, and sometimes military or private fields. The name and elevation sit next to the symbol. A data block may give the runway length, the frequency and the hours.

For a student the first things to take from an aerodrome symbol are its name, its elevation and the nearest controlled or restricted airspace. Everything else, such as the runway details, the circuit direction and the prior permission rules, comes from the AIP and the aerodrome chart. See where to find official VFR information for Romania.

7. Airspace boundaries, class letters and frequencies

Controlled airspace is drawn with a coloured band along its edge. Beside it you find the name, the class letter (A to G) and the limits. The upper limit is written above a short line and the lower limit below it. The lower limit may be the ground or sea surface, an altitude, or a flight level, and the legend tells you which figure is which.

Special-use areas such as danger, restricted and prohibited areas are drawn with a boundary and a short code, for example a letter D, R or P and a number. The legend explains how the code is built in your country. Their activity times are not always printed, and you must check them in the AIP or with the service responsible. The airspace classes and VFR minima lesson covers what each class requires.

A small box gives a frequency for the service of that area or aerodrome. Treat the chart as a pointer and confirm the frequency in a current source before you fly.

VORs, DMEs and NDBs are drawn as blue symbols with a name, an identifier and a frequency in a box. A hexagon is a VOR, a square is a DME, a ring of dots is an NDB, and a hexagon inside a square is a combined VOR/DME. Reporting points are triangles: filled for compulsory and open for on request. For what these aids do, see the lesson on VOR, NDB, DME and GNSS.

9. Landmarks for pilotage

Railways, motorways, rivers, lakes, power lines, built-up areas and woods are what you actually see out of the window. Pick checkpoints that stand out from their surroundings and cannot be confused with a neighbour: a river bend where a railway crosses is better than a field. The map reading and pilotage lesson goes into how to choose and use them.

10. The grid and magnetic variation

The chart is covered with a graticule of latitude and longitude, shown as lines, crosses or ticks. Latitude on the side of the sheet is also your distance scale: one minute of latitude is one nautical mile everywhere. Longitude is not, because meridians come together towards the pole, so do not use the longitude scale to measure distance. The lesson on latitude, longitude and distance explains this.

Dashed lines called isogonals join points with the same magnetic variation, with the value in degrees East or West and often the yearly change. Variation changes slowly with time and place, so use the value of the nearest line and the date printed on the chart. The rule for converting is:

magnetic track = true track − variation East, or + variation West

The old phrase is “East is least, West is best”. A track of 090° true with 6°E variation is 084° magnetic. The lesson on time, speed, distance and magnetic variation has more worked examples.

11. Planning a track on the chart

  1. Mark the departure and the destination, and draw a straight line between them with a sharp pencil.
  2. Measure the distance along the line with the scale bar or the plotter, in nautical miles.
  3. Measure the true track with the plotter, aligned to a meridian near the middle of the leg. Read it to the nearest degree.
  4. Find the variation from the nearest isogonal and convert to a magnetic track.
  5. Check the strip along the line, a few miles each side: the highest terrain, obstacles, airspace and special-use areas. Adjust the line if you need to.
  6. Choose checkpoints, mark them, and write the distance between them.
  7. Apply the wind for the heading and groundspeed. The lesson on the wind triangle shows how.

Gaining a feel for the numbers takes practice, so use the exercise further down this page.

12. VFR map symbols: a simplified legend

These symbols were drawn for this page. They follow the general conventions of ICAO Annex 4 in shape and colour, but they are not a copy of any chart, and national charts differ in detail. Use them to learn the ideas, then check the legend on the chart in your hand.

13. Symbol quiz and flash cards

Try it: a ten-question quiz or a set of flash cards, built from the symbols above. Choose a group to practise a few at a time.

This panel needs JavaScript. The legend above lists every symbol with its meaning.

14. Measure it: distance, true track and magnetic track

Try it: drag pins A and B on the simplified map below, which was drawn for this page and is not a real area. The panel gives the distance, how long it is on paper at your chosen scale, the true track from the protractor, and the magnetic track for the variation you set. The solid blue line is the track. The dashed black line is true north and the dotted orange line is magnetic north.

This panel needs JavaScript. The worked exercises below cover the same sums.

The map is flat and the grid squares are 10 nm. On a real Lambert chart the meridians lean slightly, so measure at a meridian near the middle of the leg. Readings are planning figures to the nearest degree.

15. Try it yourself

  1. On a 1:500,000 chart a leg measures 7.4 cm. How long is it?
    Show the answer

    7.4 × 500,000 ÷ 185,200 = 20.0 nm. As a quick check: 1 cm is 2.7 nm, and 7.4 × 2.7 is 20.

  2. On a 1:250,000 chart a leg measures 11.1 cm. How long is it?
    Show the answer

    11.1 × 250,000 ÷ 185,200 = 15.0 nm. The same 15 nm would be 5.6 cm on a 1:500,000 chart.

  3. The true track is 112° and the variation is 6°E. What is the magnetic track?
    Show the answer

    East is least: 112 − 6 = 106° magnetic.

  4. The true track is 350° and the variation is 5°W. What is the magnetic track?
    Show the answer

    West is best: 350 + 5 = 355, so 355° magnetic. With a true track of 358° the sum is 363, and you subtract 360 to get 003°.

  5. You read a figure 34 in a grid quadrangle, and the legend says the figures are in hundreds of feet. Your planned altitude is 3,000 ft. What does it tell you?
    Show the answer

    The highest terrain or obstacle in that block is about 3,400 ft, so 3,000 ft is below it. Plan a higher altitude with your own margin, or route round the block, and check the forecast cloud base.

16. Questions students ask

What scale is a VFR chart?

It depends on the country. Many VFR charts are at 1:500,000 and some areas also have 1:250,000 sheets. The scale is printed in the legend and shown as a scale bar.

What projection does an ICAO chart use?

The Annex 4 1:500,000 chart uses a Lambert conformal conic projection, and the legend names the standard parallels. Always check the legend of the chart you are using.

What is the large number in the middle of a grid square?

On many VFR charts it is the maximum elevation figure: the highest terrain or obstacle in that quadrangle, usually rounded up. Check the legend for the unit and how it is built.

How do I measure a true track on a chart?

Draw the line, place the plotter on it with its centre on a meridian near the middle of the leg, and read the angle from north. Then correct for variation to get the magnetic track.

Are the symbols the same in every country?

They are similar, because most follow ICAO Annex 4, but colours, sizes and some shapes differ. Read the legend before every new chart.

Is the VectorEFB map a chart I can navigate with?

No. VectorEFB is a planning and situational awareness aid, and it is not certified for navigation. Use the current official chart and AIP for real flights. See paper or electronic flight bag for the trade-offs.

VectorEFB is a training and planning aid. It is not certified for navigation and the symbols on this page are simplified. Check official sources, the legend of your own chart and your instructor’s method.

Next: the one-in-sixty rule. All guides are listed on the guides page.