Learning hub · Aircraft General Knowledge · Lesson 5
Inside a jet engine: the turbofan
A student pilot flies a piston aeroplane, but sooner or later you will stand next to an airliner and wonder what is inside the engine. The cutaway below shows a high-bypass turbofan hung under the wing of a commercial jet. Run it, slow it, and follow the air from the front of the engine to the back.
About 12 minutes, plus the quiz. Part of Aircraft General Knowledge. A background lesson: your own aeroplane is likely to be a piston engine, covered in the lessons before this one.
1. How a jet engine makes thrust
A propeller and a jet engine do the same job in a different way: they take air and throw it backwards, and the reaction pushes the aeroplane forwards. Thrust is the mass of air each second multiplied by how much its speed is increased. You can get the same thrust by accelerating a small mass of air a lot, as an old turbojet did, or a large mass of air a little. The second way uses far less fuel, which is why every modern airliner has a turbofan.
Try it: the diagram shows the engine slowed down, hung from a pylon under the wing, with half of the casing cut away. Use the buttons to look at one section at a time, and the fan speed slider to go from ground idle to take-off thrust. The small chart shows the gas temperature along the core.
This diagram needs JavaScript to move. The explanation below and the exercises cover the same ideas.
Typical figures, rounded and simplified, not those of any real engine. A teaching diagram. The aeroplane is not to scale.
2. The fan and the bypass
The huge fan at the front is a many-bladed propeller inside a duct. Most of the air it moves, roughly nine parts in ten in a modern engine, does not go into the engine at all. It flows around the core through the bypass duct and leaves at the back as a gentle, fast stream. The ratio of bypass air to core air is the bypass ratio. On a modern airliner engine the fan makes about four fifths of the thrust.
3. The compressors
The air that goes into the core meets a compressor made of alternating rows: a ring of rotating blades (the rotor), then a ring of fixed vanes (the stator) which straighten the flow and slow it down, turning speed into pressure. There are two compressors, a low-pressure one (the booster) behind the fan and a high-pressure one behind it. Together they raise the pressure to something like 30 to 40 times the pressure outside. Squeezing air heats it: at the end of the high-pressure compressor it is well over 500 degrees Celsius.
4. The combustor
The compressed air goes into a ring-shaped chamber. Fuel is sprayed in through a ring of nozzles and burns continuously, not in separate strokes as in a piston engine. A piston engine needs a spark for every cycle. A jet engine needs ignition only to start, and after that the flame sustains itself. Only part of the air is needed for burning. The rest is fed along the walls and mixed in to cool the gas, because the gas leaving the combustor at full power is hotter than the turbine metal would normally survive. The turbine blades are hollow and are cooled from the inside by air taken from the compressor.
5. The turbines
The hot, high-pressure gas expands through the turbines and turns them, like a windmill. The turbines do not make thrust directly: their job is to drive the compressors and the fan through the shafts. A high-pressure turbine sits right behind the combustor and drives the high-pressure compressor. Behind it, several low-pressure turbine stages drive the fan and booster through a longer shaft that runs through the middle of the first one.
That is why there are two spools. The two shafts turn at different speeds, which lets the fan turn slowly (its blade tips are fast already) while the core turns fast. The cockpit shows N1, the fan or low-pressure speed, and N2, the core or high-pressure speed, as percentages. N1 is the main indication of thrust.
6. The nozzle
The gas that is left after the turbines has still some energy. It leaves round a cone at the back as a fast jet, and the bypass air leaves round it from the duct. The exhaust gas temperature (EGT) is monitored by the crew, because it shows how hard the core is working and warns of trouble.
7. What a pilot of small aeroplanes should know
- Intake danger. A running jet engine sucks in air with great force. Stay clear of the front, and do not walk in front of an airliner engine that is turning or about to start.
- Jet blast. Behind a running engine the air moves very fast and can be hot. It can overturn a light aeroplane or throw up loose objects. Keep well clear of the back of airliners and give them space on the apron and at the holding point.
- Wake turbulence. The wake of a large aeroplane is a hazard for a light one in the air: leave extra spacing behind heavy aeroplanes. On the ground the engines add the jet blast described above.
- Slow spool-up. A jet engine takes a few seconds to go from idle to full thrust. A piston engine with a propeller responds sooner.
8. Try it yourself
Work each one out on paper first, then open the answer to compare. The numbers are invented.
- A modern turbofan has a bypass ratio of 9 to 1. At take-off the engine takes in 800 kg of air every second. How much air goes through the core and how much goes round it?
Show the answer
A bypass ratio of 9 to 1 means nine parts of bypass air for each part through the core, ten parts in all. The core gets 800 ÷ 10 = 80 kg each second and the bypass duct gets 9 × 80 = 720 kg each second.
This is why the fan makes most of the thrust: it handles nine tenths of the air.
- The high-pressure compressor of an engine raises the pressure to 38 times the outside pressure. At sea level the outside pressure is 1,013 hPa. What is the pressure at the end of the compressor? Why is the air hot there?
Show the answer
38 × 1,013 = about 38,500 hPa, or roughly 3.85 megapascals.
Compressing a gas heats it, as in a bicycle pump. At that pressure ratio the air has been heated by the compression alone to something over 500 degrees Celsius, before any fuel has been added.
- The cockpit shows N1 at 85 per cent and N2 at 94 per cent. Which one is the fan, and why is the fan speed not the same as the core speed?
Show the answer
N1 is the fan (with the low-pressure compressor and turbine). N2 is the core, the high-pressure spool.
The two spools are on separate shafts, so they can turn at different speeds. The fan is very large, so its blade tips are already fast at a modest speed of rotation, and a high speed would be harmful. The compressors and turbines in the core are small and work best at a high rotation speed. N1 is the main indication of thrust.
9. Check yourself
Five original practice questions. Answer them, press Check answers and read each explanation.
Back to the learning hub.