Learning hub · Aircraft General Knowledge · Lesson 4
Inside a piston engine: cylinders, crankshaft and oil
The first lesson on the piston engine explains the cycle. This one opens the engine up. Turn the cutaway below, slow the crankshaft down, and find every part a student pilot is expected to know: the crankshaft, the connecting rods, the valves and camshaft, the magnetos, the oil system and the propeller.
About 12 minutes, plus the quiz. Part of Aircraft General Knowledge. Read the piston engine lesson first.
1. The layout: four cylinders lying flat
Most training aeroplanes have a horizontally opposed engine, often called a flat four. Two cylinders lie on each side of a central crankcase, pointing outwards like the arms of a boxer. The layout is short, wide and well balanced, and it puts the cylinders in the airflow so they can be air-cooled by fins on the outside. The propeller is bolted straight on to the front of the crankshaft, so it turns at engine speed. There is no gearbox in most light training aeroplanes.
Try it: the engine is shown slowed down. Use the buttons to look at one system at a time, or drag the crankshaft angle to stop it at any point. The colour of the gas in each cylinder shows its stroke, and the small chart shows all four cylinders over one full cycle.
This diagram needs JavaScript to move. The explanation below and the exercises cover the same ideas.
A simplified teaching diagram of a typical engine. Real engines differ in detail, and the flight manual of your own aeroplane is what counts. Not for operational use.
2. Crankshaft, connecting rods and pistons
The piston moves in a straight line. The propeller needs to turn. A connecting rod links each piston to an offset part of the crankshaft called a throw, and the straight push on the piston becomes a turning force on the shaft. The crankshaft runs in smooth bearings called journals, and counterweights on the webs balance the moving parts so the engine does not shake itself apart.
The piston itself carries rings. They seal the gap between the piston and the cylinder wall, so the pressure of the burning gas pushes the piston and does not leak past it, and they wipe the oil film from the wall. Worn rings lose compression and let oil into the cylinder.
3. Cylinders, valves and the camshaft
Each cylinder has a head with an inlet valve and an exhaust valve, held shut by springs. The camshaft pushes them open at the right moment through lifters, pushrods and rockers. The shaft has an egg-shaped lobe for each valve, and it is geared to the crankshaft to turn at half its speed. That is because each valve must open only once in the two turns that make a full cycle.
The cylinders are cooled by air flowing over the fins, which is why the cowling has baffles to guide the air. A long climb at low speed, or a lean mixture, can make the cylinder head temperature rise. Your instruments show it. Lowering the nose, enriching the mixture and reducing power are the usual remedies.
4. Firing order
Each cylinder makes one power stroke every two turns. If all four fired together the engine would be violent and the power would come in lumps. Instead they take turns, 180 degrees of crankshaft rotation apart, in the firing order 1-3-2-4. At any moment each of the four cylinders is on a different stroke: one is making power, one is clearing the exhaust, one is drawing in mixture and one is compressing. Find that pattern in the chart in the diagram.
5. Ignition
Two magnetos sit at the back of the engine. Each one is a self-contained generator driven by the engine, so it needs no battery. Each feeds one of the two spark plugs in every cylinder, and they spark just before the piston reaches the top of the compression stroke, because the mixture takes a moment to burn. If one magneto fails, the other keeps the engine running, with a small drop in power. That is the drop you look for in the magneto check. See the first lesson for the check itself.
6. The oil system
Oil sits in the sump at the bottom of the engine. A pump draws it through a filter and sends it under pressure through passages to the crankshaft bearings, the camshaft, the valve gear and, by splash and spray, the cylinder walls. Oil does three jobs: it lubricates so metal does not touch metal, it carries heat away from places the air cannot reach, and it cleans by carrying particles to the filter.
- Oil pressure should rise within seconds of starting. If it does not rise in the time given in the flight manual, shut the engine down.
- Oil temperature shows how hard the oil is working. A high reading can mean too little oil, a lean mixture or too little cooling airflow.
- Oil quantity is checked on the dipstick before every flight. The engine uses a little oil on every flight, and the minimum quantity is in the manual.
7. The propeller
The propeller is fixed to the flange at the front of the crankshaft. In a fixed-pitch propeller the blades cannot change angle, so the RPM depends on the power the engine produces and on how fast the air flows through the disc. In a dive the RPM rises, and in a steep climb at the same throttle setting it falls. Always treat the propeller as live. It is the part of the engine that can hurt you on the ground.
7. Try it yourself
Work each one out on paper first, then open the answer to compare. The numbers are invented.
- A four-cylinder, four-stroke engine runs at 2,400 RPM. How fast does the camshaft turn? How many degrees of crankshaft rotation are there between one power stroke and the next in the whole engine, and why does that number matter?
Show the answer
The camshaft turns at half the crankshaft speed: 2,400 ÷ 2 = 1,200 RPM. Each valve opens once in every two crankshaft turns, which is why the cam can turn once in that time.
One cycle is 720 degrees of crankshaft rotation and it holds one power stroke for each of the four cylinders, so they fire every 720 ÷ 4 = 180 degrees. Spacing the power strokes evenly makes the engine run smoothly and keeps the torque on the propeller steady.
- Cylinder 1 has just fired and its power stroke is starting. Using the firing order 1-3-2-4 and 180 degrees between firings, which cylinder fires next? After how many degrees of crankshaft rotation does cylinder 2 start its power stroke? Which cylinder is on the compression stroke while cylinder 1 is making power?
Show the answer
The firing order is 1-3-2-4, so cylinder 3 fires next, 180 degrees later. Cylinder 2 follows 180 degrees after that, so it starts its power stroke 360 degrees after cylinder 1.
Cylinder 3 fires 180 degrees after cylinder 1, so during the power stroke of cylinder 1 it is the last stroke before firing: cylinder 3 is on its compression stroke. At the same moment cylinder 4 is clearing its exhaust and cylinder 2 is drawing in mixture. You can check all of this on the chart in the diagram.
- After starting, the oil pressure gauge stays at zero for 30 seconds while the engine runs at idle. What do you do, and why is waiting to see if it comes up not a good plan?
Show the answer
Shut the engine down. The pressure should rise within a few seconds, and the time allowed is in the flight manual.
With no oil pressure, the bearings, camshaft and cylinder walls are running without a proper oil film. Metal to metal contact can damage the engine in a short time, and a damaged engine can fail in flight. The fault can be a failed gauge, but you cannot tell that on the ground without checking, so the engine stays off until an engineer has looked at it.
8. Check yourself
Five original practice questions. Answer them, press Check answers and read each explanation.
Back to the learning hub.